When opening an automated garage door, you would have a remote control or a button to open it. To make it easier for the rest of the household to access the garage, having something like a LiftMaster keypad helps so that they don't need to rely on someone else pressing the button for them.
But how do you program one? We've researched how you can install a LiftMaster keypad, and this is what we found!
To program your LiftMaster keypad, follow these steps:
- Press and hold the # and * signs on the keypad until the flashing light stops.
- Locate and press the "Smart" button on your garage door opener.
- Enter your four-digit PIN on the keypad and press the "Enter" button.
- Press "0" to end the programming.
- Test your PIN code.
By following these steps, you'll be able to program your LiftMaster keypad to open and close your garage door without a remote control. Keep reading this guide as we walk you through the steps.
Programming Your LiftMaster Keypad
It's essential that what you put into your home is something you trust, which is what LiftMaster has built as a brand since its establishment in 1967.
A LiftMaster keypad would make it easier for you and your household to access your garage without relying on the remote control.
Before you start programming the keypad, remember to familiarize yourself with the location of the "Smart" button of your garage door opener and make sure that the area of the garage door is clear.
The LiftMaster keypad doesn't run on wires, so there's no need to install it beforehand. All you need to do is put in a new battery for it to function and you're all set.
See this LiftMaster keypad on Amazon.
Press And Hold The # And * Buttons
The programming starts with pressing and holding the # and * buttons of your LiftMaster keypad. You will need to hold these two buttons at the same time until the keypad starts to light up.
The light will blink a few times until it stops into a solid light.
Locate And Press The "Smart" Button On The Garage Door Opener
You may need to use a ladder for this step, as you'll have to reach the garage door opener and press a button. You should know where the "Smart" button is on your garage door opener.
This button can also be labeled "Program" or "Learn." Usually, you can find this button around the antenna wire, but if you're unsure, you can consult its manual.
Pressing this button will allow the garage door opener and the LiftMaster keypad its corresponding frequencies and pair them accordingly.
One important note to remember is that you have only 30 seconds to complete the programming after pressing the "Smart" button.
If your LiftMaster keypad is already installed into a wall and you think you can't make the 30-second time limit, ask someone else to press the button on the garage door opener for you.
That way, they can simply give you a signal when they do press the button. Just make sure that they're pressing the right one.
Enter Your Four-digit PIN On The LiftMaster Keypad
After the button is pressed, you can put your four-digit PIN on the LiftMaster keypad and press "Enter" afterward. Make sure that the PIN is something you can remember so you can also share it with your household in case they need to access the garage.
By pressing "Enter," the code would be transmitted to the garage door opener.
If the code gets accepted, the door opener should blink once. If it does not light up, press the "Enter" button on your keypad until it blinks.
Press "0" To End The Programming
After the garage door opener lights up, you may press "0" on your LiftMaster keypad to end the programming. This should signal to the system that you are done programming the keypad to your garage door opener.
Test Your PIN Code
The final step is to test out the code and see if your programming works. All you need to do is press your four-digit PIN and "Enter." Your garage door should open or close once you do this.
If you have more than one garage door opener, you must repeat the steps and have different PINs for each door. Depending on the model of your keypad, it can hold multiple PINs at once.
Programming A Temporary PIN For A LiftMaster
A garage door opener that you can open with a keypad makes it easier for people within your household to access it when needed.
It also eliminates the hassle of relying on one person or finding the remote to open the door. But there may be times when someone may need to come over and access your garage or your home.
You can opt to give them your PIN as well. However, you must change your PIN every time you give it away to avoid security issues.
This can also be a hassle since you'll always need to remember a different code. The solution to that is providing a temporary PIN instead.
As the name suggests, the temporary PIN can only work for a limited number of hours or times the door can be opened, depending on your preference.
This way, you don't always need to reset your PIN or be within the vicinity just to let someone in and still have control over access to your home.
Here are the steps to program a temporary PIN:
Enter Your Programmed PIN, Then Press And Hold The * Button
The PIN can be any PIN programmed into the LiftMaster keypad's memory. Once you've inputted the four-digit PIN, press and hold the * button until you see the garage door light blinks three times.
Register The Temporary PIN
Make the temporary four-digit PIN and press the "Enter" button. If you have multiple PINs programmed into the LiftMaster keypad, be careful not to use them as temporary PINs.
After pressing "Enter," the garage door light will flash four times.
Set The Limitations Of The Temporary PIN
You can set the temporary PIN on how many hours or times the door can open. You'll need to decide what parameters you want to work with first.
You can set it to be used up to a max of 225 hours or 225 times. Either way, you'll need to input your desired number on the LiftMaster keypad, followed by a * or #.
Suppose you decided on hours, press and hold the * button; otherwise, if you choose the frequency of the door being opened, press and hold the # button.
The garage door opener should light up one time in response. This also signals that the temporary PIN has been inputted.
Changing The Programmed PIN On Your LiftMaster
It's good practice to change your programmed PIN now and then to maintain the security of your home. Unlike the initial programming of your PIN, you won't need to reach for the garage door opener.
Enter The Programmed PIN To Be Changed
You'll need to input the four-digit PIN that you want to change. After that, press and hold the # button. You'll need to hold the button down until the light of the garage door opener flashes twice.
Register The New PIN
The light flashing twice signals you to enter your new PIN. Again, make sure the new PIN is something that you can remember. Press "Enter" once you're done.
The garage door opener should flash once to signal that your PIN has been changed successfully.
Similar to the first instructions in this article, you may try out the new PIN by inputting the new PIN on the LiftMaster keypad and pressing "Enter."
In Conclusion
If you have a LiftMaster keypad and are programming it for the first time, you will need to press and hold the # and * signs on the keypad simultaneously until the flashing light on the keypad stops.
After that, locate and press the "Smart" button of your garage door opener. You must enter your four-digit PIN on the keypad and press the "Enter" button within 30 seconds.
To end the programming, press "0," and don't forget to test your PIN code.
For more informative articles, check these out: